CAT34TS02
http://onsemi.com
10
Figure 27. EEPROM Page Write
SDA LINE
BYTE
ADDRESS (n)
DATA n
DATA n+1
SLAVE
ADDRESS
SPD
NOTE: In this example n = XXXX 0000(B); X = 1 or 0
SLAVE
BUS ACTIVITY:
MASTER
A
C
K
A
C
K
A
C
K
A
C
K
A
C
K
S
S
T
A
R
T
S
T
O
P
P
DATA n+P
Read Operations
Immediate Read
Upon powerup, the address counters for both the
Temperature Sensor (TS) and onboard EEPROM are
initialized to 00h. The TS address counter will thus point to
the Capability Register and the EEPROM address counter
will point to the first location in memory. The two address
counters may be updated by subsequent operations.
A CAT34TS02 presented with a Slave address containing
a 1 in the R/W
 position will acknowledge the Slave address
and will then start transmitting data being pointed at by the
current EEPROM data or respectively TS register address
counter. The Master stops this transmission by responding
with NoACK, followed by a STOP (Figures 28a, 28b).
Selective Read
The Read operation can be started at an address different
from the one stored in the respective address counters, by
preceding the Immediate Read sequence with a data less
Write operation. The Master sends out a START, Slave
address and address byte, but rather than following up with
data (as in a Write operation), the Master then issues another
START and continuous with an Immediate Read sequence
(Figures 29a, 29b).
Sequential EEPROM Read
EEPROM data can be read out indefinitely, as long as the
Master responds with ACK (Figure 30). The internal address
count is automatically incremented after every data byte sent
to the bus. If the end of memory is reached during continuous
Read, then the address counter wrapsaround to beginning
of memory, etc. Sequential Read works with either
Immediate Read or Selective Read, the only difference
being that in the latter case the starting address is
intentionally updated.
SLAVE
ADDRESS
SPD
TS
SDA LINE
SLAVE
BUS ACTIVITY:
MASTER
DATA
DATA (MSB)
DATA (LSB)
S
S
T
A
R
T
A
C
K
N
O
A
C
K
S
T
O
P
P
N
O
A
C
K
SLAVE
ADDRESS
BUS ACTIVITY:
MASTER
SDA LINE
SLAVE
A
C
K
A
C
K
S
S
T
A
R
T
A
C
K
P
S
T
O
P
Figure 28b. Temperature Sensor Immediate Read
Figure 28a. EEPROM Immediate Read
相关PDF资料
CAT6095VP2-GT4 IC TEMP SENSOR STAND ALONE 8TDFN
DS1621S+ IC THERMOMETER/STAT DIG 8-SOIC
DS1624S+T&R IC THERM/EEPROM DIG 256BYT 8SOIC
DS1626S+ IC THERMOMETER/STAT DIG 8-SOIC
DS1629S+T&R IC THERM/RTC/CALENDAR DIG 8-SOIC
DS1631S+T&R IC THERMOMETER DIG HI-PREC 8SOIC
DS1721U+T&R IC THERMOMETER/STAT DIG HP 8USOP
DS1722S IC THERMOMETER DIG 3-WIRE 8-SOIC
相关代理商/技术参数
CAT34TS02VP2GT4B 功能描述:板上安装温度传感器 TEMP SENSOR WITH MEMORY RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor
CAT34TS02VP2GT4C 功能描述:板上安装温度传感器 RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor
CAT34TS02VP2IGT4 功能描述:板上安装温度传感器 Temp Sensor w/memory RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor
CAT34TS04 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Digital Output Temperature Sensor with On-board SPD EEPROM
CAT34TS04EVP2GT4A 功能描述:TEMPERATURE SENSOR WITH 制造商:on semiconductor 系列:- 零件状态:在售 传感器类型:数字,本地 检测温度 - 本地:-20°C ~ 125°C 检测温度 - 远程:- 输出类型:I2C/SMBus 电压 - 电源:2.2 V ~ 5.5 V 分辨率:12 b 特性:输出开关,可编程极限,可编程分辨率,待机模式 精度 - 最高(最低):±1°C(±3°C) 测试条件:75°C ~ 95°C(-20°C ~ 125°C) 工作温度:-45°C ~ 130°C 安装类型:表面贴装 标准包装:4,000
CAT34TS04HU4GT4A 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Digital Output Temperature Sensor with On-board SPD EEPROM
CAT34TS04VP2GT4A 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Digital Output Temperature Sensor with On-board SPD EEPROM
CAT34WC02 制造商:CATALYST 制造商全称:Catalyst Semiconductor 功能描述:2-kb I2C Serial EEPROM, Serial Presence Detect